Product Description
FEATURE
Advanced MCU control pulse width modulated (PWM) technology, high efficiency operation.
Target for Gel, AGM, Conventional lead-acid (WET) and Calcium Batteries.
Built in regulator to prevent your battery from being overcharged. Overcharging occurs when the charge voltage is unregulated. This can result in premature battery failure.
Come with regulator to prevent your battery from being under charged, in the solar energy field, battery undercharge always occurs, especially on some Conventional lead -acid or Calcium batteries; The unit provides an automatic Equalization feature for deeply drained Conventional lead acid battery or Calcium battery, as well as provides a cycling automatic Equalizing feature every 28 days.
Can be connected to the battery permanently to keep the battery fully charged by using a process called "floating". This means the controller will stop charging when the battery is full and will automatically start charging the battery as required. This process will also reduce water loss and help prevent the battery from 'drying out'.
Protects your battery from discharge at night. Under low light or no light conditions the solar panel voltage could be less than the battery voltage. The unit contains a special circuit which prevents current flowing back from the battery and into the solar panel.
Colored LED to easily indicate the operational status and battery conditions.
Digital LCD to directly display battery voltage, charging current, charging capacity (Amp hour), battery types and faulty codes.
Provides plug-in remote digital display meter (Optional).
Provides external battery temperature sensor (Optional).
Multi charging protections against reverse polarity, short circuit, over temperature, over voltage, etc.
Surface Mount or Flush Panel Mount options.
Conformal-coating circuit boards and plated terminals apply to hostile environments.
SPECIFICATIONS
1 | Electrical Parameters |
|
1-1 | Rated solar panel amps SRL12-30;SRL1224-30 | 30 | Max. | AMP |
1-2 | Normal input Solar cell array voltage | 15-22 |
| VDC |
1-3 | Max. solar cell array voltage (output has no load) | 25 | Max. | VDC |
1-4 | The controller lowest operating voltage at solar or battery side | 8V | Min | VDC |
1-5 | Standby current consumption at night | 5 | Max | mA |
1-6 | Maximum voltage drop-Solar panel to battery | 0.25 | Max. | VDC |
2 | Charging characteristics |
|
2-1 | Minimum battery start charging voltage | 3 | Min | VDC |
2-2 | Soft start charging voltage | 3-10 | +/-0.2 | VDC |
2-3 | Soft start charging current (50% PWM duty) | Up to 15 | AMP |
2-4 | Bulk charge voltage | 10-14.0 | +/-0.2 | VDC |
2-5 | Absorption charging voltage at 25*C |
|
| --Gel type battery | 14.1 | +/-0.2 | VDC |
| --AGM type battery (default setting) | 14.4 | +/-0.2 | VDC |
| --WET type battery | 14.7 | +/-0.2 | VDC |
| --Calcium type battery | 14.9 | +/-0.2 | VDC |
2-6 | Absorption transits to Equalizing or Float condition: |
|
| --Charging current drops to | 1.5 | +/0.1 | AMP |
| -- or Absorption charging timer timed out | 4 |
| Hour |
2-7 | Equalization charging active |
|
| --Only for WET or Calcium battery |
|
| --Battery voltage discharged to less than | 10 | +/-0.2 | VDC |
| --Automatic equalizing charging periodical | 28 |
| Day |
2-8 | Equalization charging voltage at 25*C | 15.5 | +/-0.2 | VDC |
2-9 | Equalization charging timer timed out | 2 |
| Hour |
2-10 | Float charging voltage at 25*C | 13.6 | +/-0.2 | VDC |
2-11 | Voltage control accuracy | +/- 1% |
|
|
2-12 | Battery temperature compensation coefficient | -24 |
| mV/*C |
2-13 | Temperature compensation range | -20 ~ +50 |
| *C |
3 | Protection |
|
|
|
3-1 | Against reverse polarity or short circuit at panel or batt. |
|
3-2 | No reverse current from battery to solar at night |
|
3-3 | Over temperature protection during charging | 65 |
| *C |
4 | Electrical parts |
|
4-1 | Input output terminal | M5 terminals |
4-2 | Remote port | RL-11 (6 pins) |
5 | Physical Parameters |
|
5-1 | Controller material | Plastic, Standard ABS |
5-2 | Power terminal maximum stranded wire size | #6 AWG stranded-16 mm2 |
5-3 | Power terminal torque | Up to 17 in-lb (0.2n-m) |
5-4 | Mounting | Vertical wall mounting |
5-5 | IP grade | IP22, |
5-6 | Net weight | Approx. 300g |
6 | Environmental characteristics |
|
6-1 | Operating temperature | -25 ~ 50*C |
6-2 | Storage temperature | -40 ~ 85*C |
6-3 | Operating Humidity range | 100% no condensation |
OPERATION - L.E.D. INDICATION
The 6 LED's indicate the charging status and the battery condition |
|
|
|
|
|
|
Red | Blue | Green | Green | Yellow | Red |
Solar Power Present-No battery connected | ON | OFF | OFF | OFF | OFF | Flash |
Soft charging | ON | Flash | OFF | OFF | OFF | ON |
Bulk charging | ON | ON | OFF | Subject to battery voltage |
Absorption charging | ON | ON | OFF | ON | OFF | OFF |
Equalization charging | ON | ON | OFF | ON | OFF | OFF |
Float charging | ON | OFF | ON | OFF | OFF | OFF |
Solar panel weak | Flash | OFF | OFF | Subject to battery voltage |
At night no charge | OFF | OFF | OFF | Subject to battery voltage |
Battery Voltage below 11.5V (+/-0.2V) | ON | ON | OFF | OFF | OFF | ON |
Battery Voltage between 11.5V - 12.5V(+/-0.2V) | ON | ON | OFF | OFF | ON | OFF |
Battery Voltage above 12.5V (+/-0.2V) | ON | ON | OFF | ON | OFF | OFF |
Powerprow is a growing company focusing on the solar charge controller and power related products, being of R&D; Manufacturing and marketing; Our company is located in Shenzhen Guangdong, China. We have a sophisticated R&D team and engineers have over many years experience in this industrial field. We strive for new energy power related products, including solar charge controller, LED power supply, dual battery system, battery monitor accessories, etc; The products are with our own in-house designed software, and established with Powerprow own features and performance, in addition, the combination of the flexible software and hardware makes our products more adaptable to customer's demanding and applications.
Our company is certified by ISO9001: 2008 quality system, from the customer PO to the final goods delivery, all processes are under the control of ERP system, we are a self-contained manufacturer and equipped with our own SMT, wave soldering, burn-in testing facilities and processes.
We are committed to provide the "one-stop" new energy power related solution and service to our clients.